Ways You Can Plumb Your Own House

Were you aware that winterizing your plumbing system is nearly free and can save you potentially thousands of dollars of repairs. If this advice sounds appealing to you, then be sure to check out more of the expert advice given in this article. You will be much happier than if you had to deal with a water crisis during the middle of winter.

You always want to solder correctly, the biggest mistake most people make when soldering is failing to get the interior of the fitting and the exterior of the pipe clean and shiny. Polish these surfaces with a fine emery clot until bright. When soldering, never heat the pipe, but instead heat the fitting. Doing so allows the solder to be drawn into the fitting by capillary action.

Act quickly if your pipes freeze! Shut off informative post and open the faucet, enabling it to drain when it thaws. Starting with the faucet, and working your way to the iced-up area, aim a propane torch or hairdryer at the pipe - this will quickly defrost it. You could also wrap the pipe in a heating pad or aim a heat lamp at it, but this will take quite some time. A last resort is to wrap the pipe in rags and pour boiling water over it.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

If your toilet will not flush, and there is very little water in the basin, try to fix the issue by dumping warm water in the bowl from around your waist line. Repeat this as many times as necessary until your clog is gone, and you can flush normally once again.

If your sink is letting rusty water out and it will not drain, it is mostly likely because of the biological scum and grease that is built up in the pipes. Edmonton Central Air Conditioning need to have your drains professionally cleaned, allowing maximum flow through your drains. Your drains must be open completely.

If you have an automatic sprinkler system, you want to consider getting a spring-loaded timer which can be attached directly to your hose. This prevents your lawn from getting too much water in case you forget to turn your system off. Getting too much water could kill your grass and plants.


While it may seem like a seemingly harmless thing to do, never run potato peels through your garbage disposal. The chemical make up of this seemingly harmless food allows the potato to turn into a thick, viscous substance that can wreak havoc on the disposal itself, with the potential to render it completely useless.

During the week, hair and soap can build up in your drains and can cause serious clogs. Make sure that you have strainers in each of your drains to help catch this debris so that it does not become an issue. This will help to keep your water flowing efficiently.

Never pour grease down the kitchen-sink drain. This will help you avoid clogs in your kitchen sink. Place grease in a can or other receptacles and dispose of in the trash. Grease that has congealed on pots, and pans can be wiped off with paper towels that can be thrown in the trash.

Look online for reviews of the plumbing contractor you are thinking of hiring. If people are not satisfied with the work that the plumber preforms, many times they will go on the internet and post negative reviews. If they are happy with the plumber they will also post positive reviews.

Don't start any do-it-yourself plumbing project without having a plan in place. You need to know beforehand exactly what you are getting yourself into. Know what kind of space you are working with and what lines are which. Getting a clear picture early on will make your plumbing project go a lot smoother!

Use a product like BioBen if you are planning to leave your system shut off for a few weeks. Water will still remain in the pipes and could start smelling because it is not moving. This type of product will keep the water from stagnating and from smelling too bad.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.

Yes, plumbing is quite a subject in that it is completely subjective by it's very definition. No two people view plumbing the exact same way. What one finds useful to their system, the other may not. These tips should have given you some advice on how to start with your own plumbing.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Ways You Can Plumb Your Own House”

Leave a Reply

Gravatar